Serving Southern & Midcoast Maine
Licensed & Insured  •  Efficiency Maine Registered Vendor
BANN Homeowner Resource

Do I Need a Panel Upgrade for a Heat Pump in Maine?

If you’re planning to switch from oil to ductless heat pumps, one of the first questions is whether your electrical panel can handle it. Sometimes the answer is yes with no changes. Sometimes it needs a few new breakers. And sometimes the panel or the whole electrical service needs an upgrade first. Here’s how to tell, and what we look at before quoting a heat pump install.

Why Heat Pumps Affect Your Panel

Each outdoor heat pump unit needs its own dedicated 240-volt circuit, which takes two spaces in your panel. A whole-home system with two or three outdoor units can add several new circuits, and in winter those units run for long stretches. The question isn’t only whether there’s room in the panel. It’s whether your service has enough capacity for everything the house already uses, plus the heat pumps, on the coldest day of the year.

What an Electrician Checks

  • Service size. Most Maine homes have 100 amp or 200 amp service. Older homes may still have 60 amp service.
  • A load calculation. We add up what the house already uses, including electric water heaters, ranges, dryers, well pumps and EV chargers, and then add the new heat pump load. This is what tells us whether the service is big enough.
  • Open spaces in the panel. Each outdoor unit needs two spaces. A full panel may need a subpanel or replacement.
  • Panel condition and brand. Fuse boxes, corroded panels and some older brands like Federal Pacific and Zinsco usually get replaced rather than added to.
  • Future plans. If an EV charger, an addition or a generator hookup is coming, it’s often cheaper to size the upgrade for that now.
New 200 amp electrical panel installed during a service upgrade by BANN in Topsham, ME
A new 200 amp panel installed during a service upgrade in Topsham, with room for heat pumps and an EV charger.

When You Usually Don’t Need an Upgrade

Many homes with 200 amp service and open spaces in the panel can take one or two outdoor heat pump units without an upgrade, especially if the house doesn’t already have big electric loads. Even some 100 amp homes can handle a single unit after a load calculation. The only way to know for sure is to check your panel and run the numbers.

Signs You’ll Probably Need One

  • You have a fuse box, or 60 amp service.
  • Your panel has no open spaces and is already full of tandem breakers.
  • You already have electric heat, an electric water heater, an electric range and a dryer, and you’re adding a whole-home heat pump system.
  • Breakers trip often, or the panel is warm, rusty, scorched or buzzing.
  • You’re also planning an EV charger.
Old fuse panel before a 100 amp panel replacement by BANN in Harpswell, ME
An old fuse panel before replacement in Harpswell. Panels like this usually get replaced before adding heat pumps.

Panel Replacement vs. Service Upgrade

A panel replacement swaps the breaker box but keeps the same service size. It fixes an old, unsafe or full panel. A service upgrade increases the capacity coming into the house, for example from 100 to 200 amps, and usually includes a new meter socket and coordination with your utility, which is Central Maine Power for most of our service area. If the load calculation shows the house needs more capacity, it’s a service upgrade. Learn more on our panel and service upgrade page.

Plan the Electrical and the Heat Pump Together

The smoothest installs are the ones where the electrical side is planned up front. At BANN, we install Daikin and Bosch cold-climate heat pumps and do the electrical ourselves, so the panel check, circuits, disconnects and any upgrade are part of one plan and one price. See our heat pump installation page, and check current Efficiency Maine rebates for qualifying heat pump installs. Efficiency Maine decides eligibility and amounts.

Heat Pump and Panel FAQ

Can a 100 amp panel handle a heat pump?

Often, yes, for one or two outdoor units, but it depends on what else the house uses. A load calculation tells us whether 100 amps is enough.

How many circuits does a heat pump need?

Each outdoor unit typically needs its own dedicated 240-volt circuit. Indoor heads are usually powered from the outdoor unit.

How long does a panel upgrade take?

A panel replacement is often done in a day. A service upgrade can take longer because it may need a utility disconnect and reconnect and an inspection.

Do I need a permit for a panel upgrade in Maine?

Yes. Panel and service upgrades need an electrical permit and inspection. We pull the permit when one is required.

Can you do the panel upgrade and heat pump install together?

Yes. We do both, so the electrical work is planned with the heat pump install instead of as a separate job.

Not Sure Your Panel Can Handle a Heat Pump?

We’ll check your panel and service, run the numbers and tell you exactly what your home needs before you buy anything.

Heat Pump InstallationCall 207-406-3918